Mr. Heater TE8001 Spezifikationen PDF herunterladen

The TE8001 is an electronic non-programmable thermostat. It is designed to work with most

standard single stage heating and/or single stage cooling systems. These include single or dual

transformer 24 VAC gas, oil or electric heating, and 24 VAC cooling systems. This thermostat

is also compatible with single stage heat pumps.

The TE8001 is designed to operate entirely on two AAA alkaline batteries, or 24 volts from the

heating/cooling system’s transformer, using the batteries only for memory back up.

FORM: 8063

Rev: -

Installation:

Important: Read the entire instructions before beginning installation. Failure to follow these

instructions could result in personal injury and/or property damage.

Location:

The thermostat should be mounted 4 to 5 feet above the floor in a location where it will be

exposed to average room temperature. The thermostat must not be mounted where it will be

effected by a source of heat such as lamps, sunlight, fireplaces, pipes, registers, etc..., or

sources of cold such as windows, doors, drafts, etc... The thermostat must not be mounted on

an exterior wall, behind a door, or in an alcove. Such locations will inhibit the thermostat’s

ability to accurately control room temperature

Removing existing thermostat:

Caution:

Power must be disconnected before removing existing wiring connections from thermostat to

prevent possible electrical shock and/or equipment damage. All wiring must conform to local

and national electrical codes and regulations.

1: Remove existing wiring by writing down each of the wire’s colors and the designation of the

terminals that they are connected to. If more than one wire has the same color, tag the wire

with some form of identification.

2: Remove wires from thermostat.

Mounting:

This thermostat may be mounted directly to the wall, by using the mounting screws supplied.

Remove base from front section, by opening battery door, remove batteries. Pull case apart.

To mount directly to a wall use holes located in top and bottom of case.

Pull wires through hole in center of case.

Do not depend upon the thermostat as the sole means

of disconnecting power when installing or servicing the product it is

controlling. Always disconnect power at the main circuit breaker as

described above. Failure to do so may result in fatal electric shock.

TE8001 Installation & Operation Manual

TPI Corporation, Johnson City, TN 37602

Tel: 423-477-4131, Fax:423-477-0545

Diagram 3: Single Stage Heat Pump

1: Connect the transformer hot wire to the RC terminal.

2: Connect jumper between RC and RH terminals

3: Connect compressor to the Y terminal.

4: Connect jumper wire between the Y and W terminals.

5: Connect Fan to G terminal

6: Connect reversing valve to O terminals if reversing valve is activated in the

cool mode (most common), or to the B terminal if reversing valve is to be acti-

vated in the heating model.

7: Connect transformer common wire to C terminal (optional) if you wish thermo-

stat to be powered from the transformer. Without this connection, thermostat will

be powered from AAA batteries.

RH W

WIRING DIAGRAM 3.

Installing Thermostat onto base:

Once the wires have been connected to the base, and the options selected, it is

time to install thermostat onto the base. Close the battery compartment door. Do

not install batteries yet. Align the thermostat with base, and push together. Open

battery door and install batteries.

Operation:

1: Select Heat or Cool with Heat/Off/Cool Switch:

2: The display will indicate current room temperature, and display a flame if the

heat mode has been selected or a snow flake if the cool mode has been selected.

3: Press up or down arrow to set desired temperature. “SET TEMP” will appear in

the display to indicate you are setting the temperature.

4: Whenever the thermostat is activating the heating or cooling system, the word

“ON” will appear in the display.

5: Whenever you change modes (from heat to cool or cool to heat), the

thermostat will remember the last temperature set in that mode. The heat setting

and cooling setting do not have to be the same.

1 2 3 4 5 6 ... 18 19

Inhaltsverzeichnis

Seite 1 - Rev:

The TE8001 is an electronic non-programmable thermostat. It is designed to work with moststandard single stage heating and/or single stage cooling sys

Seite 2

REED SWITCHTHERMOSTATIMPORTANT: OWNER SHOULD RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCEINSTALLATION INSTRUCTIONSDESCRIPTION:The UT9001 Reed Switch

Seite 3

DIFFERENTIALDIFFERENTIALDIFFERENTIALDIFFERENTIALDIFFERENTIAL HEAT APPROXIMATELY...2OF COOLING APPROXIMATELY...4OF HEAT ANTICIPATOR MODEL...1/2

Seite 4 - Manual For

INSTALLATION AND OPERATION MANUALEPET SERIES EXPLOSION PROOF THERMOSTATS The Columbus Electric EPET Series thermostat is designed to control heating

Seite 5

HEATL1 L2NCNOCCOOLNCNOCL1 L2HEATNCNOCL1L2COOLL1L2NCNOCL1NCNOCHEATL2COOLCHANGE *OVERSWITCHL1NCNOCHEATCOOLL2CHANGE *OVERSWITCHDIAGRAMSFIG. 1FIG. 2TYPI

Seite 6

Seite 7

Seite 8

Seite 9

Seite 10 - THERMOSTAT

Seite 11

L__Y-01 SERIES TPI CORPORATION PO BOX 4973JOHNSON CITY, TN 37602INSTALLATION INSTRUCTIONSAPPLICATIONThe L series are designed for use as

Seite 12 - INSTALLATION

23Wiring:The chart is a cross reference forterminal functionality. No applicationwill require connections to all terminals.If connecting to a single t

Seite 13 - DIAGRAMS

Low Battery Indicator:Whenever the batteries start to get low, a low battery indicator ‘ ‘ will appear inthe display. Change batteries as soon a

Seite 14

6 Manual ForTE8001 ThermostatTPI Corporation PO Box 4973Johnson City, TN 37602Tel: 423-477-4131, Fax:423-477-0545www.tpicorp.comProducts manuf

Seite 15

Seite 16

Columbus Electric Division of TPI, PO Box 4973, Johnson City, TN 37602: Tel 800-251-7828, Fax 423-477-0545: REV120303UT Thermostats Installation Ins

Seite 17

Columbus Electric Division of TPI, PO Box 4973, Johnson City, TN 37602: Tel 800-251-7828, Fax 423-477-0545: REV120303Check the wiring:CAUTION D

Seite 18

REED SWITCHTHERMOSTATIMPORTANT: OWNER SHOULD RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCEINSTALLATION INSTRUCTIONSDESCRIPTION:The UT5001 Reed Switch

Seite 19 - L__Y-01 SERIES

REED SWITCHTHERMOSTATIMPORTANT: OWNER SHOULD RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCEINSTALLATION INSTRUCTIONSDESCRIPTION:The UT6001 Reed Switch

Kommentare zu diesen Handbüchern

Keine Kommentare

Mr. Heater TE8001 Spezifikationen

Stöbern Sie online oder laden Sie Spezifikationen nach Thermostate Mr. Heater TE8001 herunter. Mr. Heater TE8001 Specifications Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern